Planning applications in TQ1
We hold 1,032 planning applications for the TQ1 postcode area, 92 of them submitted in the past year. 79% of decided applications here were approved. A decision typically takes 55 days. The area is covered by Torbay, Teignbridge.
Towns and villages in TQ1
Councils covering TQ1
Recent applications in TQ1
T1 Mature Oak - Crown raise by approximately 2-3 meters, to achieve suitable clearance from understory parking area.
We have been requested to remove a dead Cedar tree in the rear garden of the above address, the tree is a mature tree and is within a area covered with TPOs
Fell mature moribund Horse Chestnut
T2 Spruce, height to be reduced by 2.5m. eastern, southern, and western aspects of the canopy, to have branches shortened by 1.5m to balance, where tree being suppressed by neighboring Monterey cypress. pre pruning dimensions: h. 16m w. 8m post pruning dimensions: h. 13.5m w. 6.5m
T1 Copper Beech: height to be reduced by 1m, target/selective prune on all sides to shorten over extended laterals, to keep tree nicely shaped. Pre pruning dimensions: H. 14m W. 8m Post pruning dimensions: H. 13m W. 7m G2 Bay (Boundary trees, two groups) Shorten height by up to 2m creating more of a consistent hedge line.
T1 remove epicormic growth on main stem up to height of adjacent wall (2m) T2 pollard at 4.5m.
T001- Holm Oak - Sectional Dismantle, See tree survey for justification.
T1 - Mimosa (Acacia dealbata) - Post mature Mimosa, situated to the front of the property - In a state of decline with basal decay and fruiting bodies - Historic poor pruning has resulted in failure of 50 % of the crown in recent storms. To be felled with the stump ground a minimum of 300mm below immediate ground level. Replacement - Supply and plant x1 Acacia dealbata (mimosa) 6-8cm coco/cont as an entrance feature tree.
T006 - 1x Western Red Cedar (Thuja plicata) ///drank.axed.trader- Sectionally dismantle, fell, and remove to ground level using appropriate dismantling techniques to ensure the safe and controlled removal of all sections. Re-Placement Tree Planting Specification To plant 1x Selected Standard Ginkgo (Ginkgo biloba) 30 litre pot,10 - 12cm girth, approximately 3.0 metres in height. See QTRA for justification
We are planning to conduct emergancy tree work on a dead tree at Torre Church of England Academy, Barton Road, Torquay, TQ1 4DN
G1 - Dismantle and fell x6 small Lawson Cypress due to close proximity of the home plus causing excessive shading. Trees outside of risk zone to remain and no works carried out on the existing hedge line behind. low amenity value and recommend replanting smaller garden trees/shrubs.
T001- Pine Proposed Works: Reduce the western (left-hand) lateral crown by approximately 2.0-2.5 metres back to suitable secondary growth to reduce end weight and rebalance the crown whilst retaining the tree's natural form. Remove the single lower lateral limb overhanging the garden (approximately 200mm diameter at the point of removal). Remove any dead, damaged or broken branches encountered during the works. All pruning to be undertaken in accordance with BS3998:2010 - Tree Work - Recommendations. Reason for Works: To reduce the dominance and leverage of the extended lateral limb, improve crown balance and lessen the visual impact over the garden whilst retaining the tree as a significant landscape feature. The removal of the lower limb will improve clearance beneath the canopy and facilitate ongoing garden use and maintenance. The proposed works represent routine arboricultural management and are not intended to adversely affect the long-term health or amenity value of the tree.
T1 - Cypress: Fell to near ground level.
Lime (T1) - I am writing to give formal notice under the five day exemption for urgent works to T1 Lime at Warberry Lodge, Higher Warberry Road Torquay TQ1 1SD. The tree is a lapsed pollard that has recently suffered a catastrophic limb failure, resulting in the loss of approximately half of its crown. The failure has exposed extensive, structurally unsound wood at the historic pollard head and left the remaining crown severely imbalanced, with significant torsional loading on the remaining scaffold limbs. The remaining structure is now asymmetrical and unstable, subject to further unpredictable failure, compromised at the old pollard points, and located directly above a regularly occupied garden with pedestrian access beneath the crown. Given the scale of the failure and the compromised structural integrity of the remaining crown, the tree now presents an immediate and unacceptable risk. The situation meets the criteria for urgent works under the exemption. The tree is a lapsed pollard. Although decay is present within the historic pollard head, the management option is to reintroduce the pollard cycle. Re-pollarding will significantly reduce crown mass and place greater leverage on the weakened pollard head, lowering the risk of structural failure while retaining the tree within the landscape. However, it will also add extra stress from heavy reduction and heat waves, possibly causing the tree to weaken further.
T13 Lime Dismantle and fell close to ground level. All works to be carried out in accordance with BS 3998:2010 Tree Work ? Recommendations. Remove all cut material from site and return to a Teign Trees depot for recycling, leaving the area safe, clean and tidy.
Oak (T1) - Branch reduction by up to 1 metre within the crown on the tree's western aspect, which is heavily leaning and slowly affecting the driveway; the tree is not visible to the wider public.
Oak (T1) - crown reduction
Construction of extension to rear.
Because of the extreme height of the tree and being situated on a bank at the rear of my garden I am requesting 50% trimming of height after visit from a tree surgeon. It is an Oak tree with 3 large branches off the trunk. The area on the bank has very strong winds and very concerned as it has grown a lot since the 5 years I have been here and seems much higher than neighbouring trees. If it fell would land on my conservatory and probably roof of the house. I am happy for you to come and view it. reduction of 3 branches from main crown to 50% above ground level, to provide sufficient clearance to property.
Silver birch tree front of our property.
5 day notice - to remove dead poplar (T1) and replace with Sorbus aucuparia
I am applying to remove one large Eucalyptus nitens. This tree is growing close to the boundary with Suncourt about half-way between the highway and the house. It is in the region of 20m in height. General The garden has been carefully designed and has been noted for the variety and quality of its plants. The area around the tree is tightly planted with trees (as can be see from Drawing_01) including the following: Gleditsia triacanthos, Magnolia officinalis var biloba, Phoenix canariensis, Magnolia grandiflora, Catalpa bignionoides 'Aurea', . All these are large including the P. canariensis. There is a smaller Butia capitata and a Cornus cousa further away. In addition there are large shrubs including a Japanese maple, Tetrapanax, Viburnum and Camellia Glycerinia as a windbreak, Pseudopanax ferox as well as countless Trachycarpus fortunei. There is a large plane tree in the highway which largely screens these plantings from the roadway, especially during summer. Reasons for works 1. In common with other Eucalyptus which I have had growing in the garden and which have quite rapidly died, this tree has a large scar on its western side. The dimensions of the scar are about 1300mm by 150mm (at the widest). The inner wood is fully exposed, is soft and is discoloured. This defect is not apparent from the eastern (our) side of the tree. I have been advised that this tree will probably not survive more than another year or two. It may be relevant that a much smaller neighbouring Eucalyptus niphophila has recently fully died. 2. My neighbour in Suncourt has been telling me that he is concerned that the tree is growing too close to his boundary wall and large paved area which he fears may be damaged by its shallow roots. 3. My main concern is that the tree - given its height and exposure to winds in the Meadfoot Valley - now poses a risk by falling either onto the Southern Comfort driveway or onto the Suncourt one. It is thus constitutes a danger to persons
Boundary Trees on Lower Woodfield Road T1 & T2 - 2 - Yew trees, T3 -1 - Turkey Oak and T4 & T5 - 2 - Holm Oaks located along the boundary adjacent to Lower Woodfield Road Crown lift to provide a vertical clearance of approximately 5.6 metres between ground level and the lowest foliage tips, pruning secondary and sub-lateral branch growth only, to achieve suitable highway regulations clearance. All works shall retain the natural form of the crown and avoid the creation of large pruning wounds. Individual pruning wounds shall not exceed 60 mm in diameter. T6 -1 - Mature Turkey Oak Remove 2 - dead branches overhanging the road, pruning back to suitable growth points. Dead branch Individual pruning wounds shall not exceed 60 mm in diameter. T7 - 1 - Austrian Pine Crown lift by removing the lowest primary branch to provide a vertical clearance of approximately 5.6 metres above road level, pruning back to the main stem to achieve highway regulation height. Reduce 1 - lateral primary branch overhanging the road & overhead BT Cable by removing approximately 2.0 metres from the branch tips, pruning back to suitable growth points. All works shall retain the natural form of the crown and avoid the creation of large pruning wounds. Individual pruning wounds shall not exceed 60 mm in diameter. Boundary Tree on Higher Woodfield Road T8 - 1 - Common Pear Tree Crown lift to provide a vertical clearance of approximately 5.6 metres above road level, pruning secondary and sub-lateral branch growth only, to achieve regulation highway height clearance. All works shall retain the natural form of the crown and avoid the creation of large pruning wounds. Individual pruning wounds shall not exceed 40 mm in diameter. All works to be carried out in accordance with BS 39982010 Tree Work - Recommendations. Justification and reasons for work within the attached document
5 Day Notice - Fell dead Ash tree. Significant Ash dieback with canopy 100% dead.
This message serves as a formal notice under the five day urgent works exemption for works to a hazardous tree within the grounds of Oakwood, Lower Warberry Road, Torquay, TQ1 1QP. A taller Sycamore within the garden has failed, with full rootplate uplift, collapsing outward across the garden and falling directly onto the smaller Sycamore, closer to the roadside but still within the garden. The impact has caused significant structural damage to the roadside tree, including crown displacement, asymmetric loading and probable fibre deformation, leaving it at increased risk of progressive failure. The damaged roadside Sycamore stands immediately above the public pavement, where no parking restrictions concentrate pedestrian movement within the potential failure zone. The combination of sudden primary failure, secondary impact trauma, and exposure to the public highway creates an immediate and unacceptable risk, bringing the works clearly within the scope of the five day urgent works exemption.
Non-material amendment relating to P/2026/0025. Amendments sought: relocation of kitchen, replacement of windows and patio doors for bi-folding doors to rear, widening of path, relocation of front door and installation of curved retaining wall.
5 Day Notice - T1 & T2 - Removal of dead & dangerous trees. The trees have been monitored in decline over several years. Trees now completely Dead and starting to decay at the base. Please see photos.
Construction of single-storey rear extension, including installation of rooflight with associated internal alterations.
T863 Monterey pine - fell
Monterey cypress (T1) - due to structural defects, recent limb failure, and overall condition of the tree, removal and replacement is recommended as the most appropriate management option to mitigate the risk of further failure.
Complete removal of dangerous leaning Cyprus pine tree.
T1 - Lime Crown reduction by up to 3 m across the entire canopy, proportionally decreasing height and lateral spread. Final pruning cuts should be made at the positions shown in the submitted photographs (red-marked cut points). All cuts to be made to suitable secondary growth points, preserving a balanced, natural crown shape. Maximum wound size should be kept as small as practicable and in line with BS3998:2010 Tree Work - Recommendations. Justification for Works The tree shows poor bifurcation, developing a single dominant stem with limited structural division. Crown reduction will decrease end-weight, reduce mechanical stress, and help maintain the tree at a size suitable for its environment. The works are preventative and aim to keep the tree structurally sound. T2 - Horse Chestnut Crown reduction by up to 3 metres, maintaining the natural crown shape. Final pruning cuts should follow the positions shown in the submitted photographs. Pruning aims to reduce end-weight and mechanical loading on the cavity located just below the first-order branch junction. All cuts are to be made to appropriate secondary growth points, in accordance with BS3998:2010. Justification for Work A cavity is present below the first-order branch junction, which reduces the structural integrity at a key load-bearing point. Crown reduction will decrease lever arm forces acting on the defective area and mitigate the risk of branch or stem failure. The work is proportionate, preventive, and intended to safely retain the tree.
As per the work spec within the report. A previous application was turned down and a question was asked about how long the probe was used to measure the decay within the crown the probe was 8 inches long.
T12 & T13 - 2x Monterey Cypress - Crown lift by removing primary, secondary and sub-lateral branch growth, to provide a vertical clearance of approximately 5.60 m between ground level and the lowest foliage tips, thereby achieving the desired clearance over the road. Individual pruning wounds shall not exceed 100 mm in diameter in accordance with BS 39982010 Tree Work - Recommendations. Remove dead or broken branches and stubs left from previous tree pruning operations, where such material exceeds 20 mm in diameter. T10 - 1x Beech Tree Crown reduce the tree overall by pruning back to the previous pruning points, whilst retaining the main framework and natural shape of the crown, thereby maintaining a high proportion of the foliage-bearing structure. Reduce the height of the tree by approximately 2.0 metres, leaving a final overall height of approximately 8.0 metres. Reduce the radial crown spread by approximately 2.0 metres, leaving a final radial spread of approximately 8.0 metres at all compass points. Individual final pruning wounds shall not exceed 40 mm in diameter. T16 - 1x Beech Tree Crown lift over the driveway only by removing secondary and sub-lateral branch growth, to provide a vertical clearance of approximately 6.0 metres between ground level and the lowest foliage tips, thereby achieving the desired clearance. All works shall retain the natural form of the crown and avoid the creation of large pruning wounds. Individual pruning wounds shall not exceed 40 mm in diameter. All arisings to be removed from site and returned to a Devon Tree Services depot for recycling, leaving the area safe, clean, and tidy. TPO & Conservation Area Application -Justification Statement The proposed tree works form part of an ongoing cyclical management programme aimed at maintaining the long term health, structural integrity and safe retention of the tree stock. Continued on JS25.03.26. See attached.
Formation of one detached dwelling (pursuant to outline planning permission P/2018/1281).
Please refer to attached tree report for comments. Work spec: 777 Monterey Cypress: Reduce the side of the western crown by 2.5m by selective branch removal. Crown raise the eastern stem to 5m above ground level to reduce load on the sagged limb. Prune to achieve a 2m clearance from the garage. Prune to achieve a 1m clearance from the telecoms wore. Use a maximum cut diameter of 125mm. Comments: Main stem divides at 1.5m into 5 stems. Some included bark present but no signs of excessive movement. The stems are extensive and have notable leans, most of all in the SW stem. The crown density is below average, more so in southern stem where there is several dead branches 100mm diameter. The eastern stem is subdominant, it looks to have sagged and likely contains some cracking. 778 Monterey Cypress: Reduce the spread of the lowest 2 limbs in the eastern aspect by 1.5m by selective branch removal. Remove hanging branches at approximately 12m above ground level. Use a 100mm maximum cut diameter. Comments: Triple stemmed from 1.5m. significant crown bias to the east. Ivy on main stems. Extensive lateral branches in eastern aspect. There is at least one broken branch suspended over the neighbours garage at approximately 12m above ground level. 779 Monterey Cypress: Remove the hanging branch near the top of the tree. Remove ivy. Prune to achieve a 2m clearance from the garage. Reduce the spread of lowest eastern branch by 2m and crown raise it by 2m. Use a 100mm maximum cut diameter. Comments: Dog-legged main stem with significant crown bias to the SW. Crown growing with 1m of garage. Ivy growth on main stem. Volume of decay suspected in main stem. Obscured by ivy, but considered contained. Lowest branch in eastern aspect is extensive with excessive end loading suspected. There is a hanging branch near the top of the tree, suspended over the garage roof. 780 Monterey Cypress: Reduce the southwestern side of the crown by 2m, targeting the cracked limb. Reduce the heig
Two storey side extension, rear single storey extension, alterations to existing patio and associated works.
Variation of condition relating to application P/2022/1313 (Formation of new porch and replacement of existing conservatory with a new single storey flat roof extension). Condition P1: Approved Plans. Variation sought: change design of porch.
Certificate of lawfulness for proposed change of use from six-bed HMO to seven-bed HMO.
Notice - Certified site under caravan sites and control of development act 1960 (Paragraph 5)
Justification for Felling T2 and T3 Pittosporum 1. Species Unsuitability for the Location Both T2 and T3 are Pittosporum, a species generally used as ornamental screening shrubs. They are not suitable for long-term retention as large trees in a confined, built-up commercial setting. When allowed to grow beyond their intended size, Pittosporum develop: - Weak, multi-stemmed forms - Shallow, spreading root systems - Poor structural resilience under load This makes them unsuitable for retention near buildings, walls, and guest areas. 2. Structural Damage to the Retaining Wall The trees are causing active structural damage to the stone wall at the hotel entrance. Signs include: - A full-height vertical split - Outward displacement of masonry - Root pressure from behind the wall Ivy-laden stems worsen moisture retention and decay. This represents direct physical damage, which is a valid and accepted reason for felling within a TPO Area. 3. Foreseeable Risk of Failure The combination of: - Root pressure against a failing wall - Multi-stemmed, ivy-laden crowns - Suppressed growth form coupled with proximity to the hotel entrance, driveway, and pedestrian routes, creates a foreseeable risk of partial or complete tree failure. In a hotel environment with constant public access, the acceptable risk threshold is low. Pruning would not resolve the underlying structural issues and could accelerate decline, contrary to BS3998:2010. 4. Limited Management Options Crown reduction would not relieve root pressure or stabilise the failing wall. Repeated pruning would create large wounds and increase the risk of decay. Root pruning is not feasible without destabilising the trees or further damaging the wall. Retention would require wall reconstruction, which cannot be safely undertaken while the trees remain in place. Felling is therefore the only proportionate and practical option. 5. Replacement Planting Commitment To uphold the amenity value within the TPO Area
T1354 - Dead Wyche elm - section fell to ground level. T1355 - Field maples - reduce tree to allow 1.5 m high pollard. Vitality poor - tree historic coppice and of unusual form. Multi stemmed and historically had significant works leading to significant wounding. The tree has deadwood throughout the canopy and the majority of primary stems has wounding and significant decay present. T1356 - Field maple - Crown reduce the tree by 1.5 m in height and crown spread. - Vitality fair - Bark included junction at 1 metre above ground level - large amounts of reactive tissue mildly mitigate likelihood of failure. The tree is 9m tall and a crown spread of 7 metres, after the reduction the tree will have a height of approx 7.5 tall and a crown spread of 5.5. metres. G2 - Mixed species (Tulip trees & Black hybrid poplars) - Reduce canopy back by 2m growing over the car park - Vitality fair - trees have deadwood throughout canopy over target areas Branches are elongated which is typical of species. The trees are currently 20 metres tall and a crown spread of 9m. After the pruning the crown spread will be approx 7m. T5099 - Dead Rowan - straight fell from ground level.
T1 Ash (Fell, stump to remain) T1 is an Ash tree that, based on its size, was clearly planted after 1967 and therefore does not fall under historic TPO protection. The upper crown of the Ash is directly interfering with the first-order branches of the adjacent Oak, disrupting its natural crown architecture and long-term structural development. Felling is required to prevent ongoing suppression and deformation of the Oaks primary scaffold limbs. The stump must remain in place, as removal would damage the Oak?s structural root plate, which provides essential anchorage and stability. T2 Oak (Repollard) T2 is an Oak that, from its size, was evidently planted after 1967. The crown shows visible decline, with reduced vitality and dieback consistent with stress and age-related retrenchment. Repollarding is recommended to reduce biomechanical loading, slow the decline process, and retain the tree safely within its setting. This approach aligns with BS3998:2010 guidance for managing declining pollards. T3 Oak (Coppice following failure) T3 has already suffered partial failure due to a combination of structural and physiological defects. A large vertical cavity in the lower stem indicates advanced internal decay, and the loss of key structural components has left the remaining sections unstable. Bark and sapwood deterioration, combined with exposed, non-adaptive tissues, show a very low likelihood of recovery. The tree presents a clear risk of further failure, and pruning is not a viable mitigation. Coppicing is advised to reduce risk while allowing regrowth from a stable base. T4 Mimosa (Fell) T4 is a Mimosa that, based on its size, was planted after 1967 and is not visible to the wider public. The tree?s slender form and limited structural robustness make it unsuitable for long-term retention. Felling is appropriate due to its low amenity value, limited public visibility, and species-specific structural limitations. T5 Lawsons Cypress (Fell) T5 is a Lawsons
5 Day Notice - T1 (Pittosporum) - Has suffered structural failure with part of the crown having already fallen and now presents an immediate and unacceptable risk to site users and the adjacent public realm. A basic location plan and supporting photographs are attached. The proposed works are restricted to the removal of the failed and hazardous material only
Non-material amendment relating to P/2025/0552. Amendment sought: description to note reduction from six apartments to five apartments & substitute drawing plan 2501-102B with 2501-102D
T1 Scots Pine - This tree lost a couple of branches during the recent storm. In order to protect the tree we would like to carry out some minor crown thinning by about 20% to reduce wind sail area. T2 Spruce - This tree is approximately 60ft in height and is located quite close to the rear of the property. A fir tree of similar height came down during the recent storms and we are concerned that this tree may also have fallen. It was noted to be swaying much more than normal and when stood on the ground beneath it a small amount of movement could be felt. We would therefore like to reduce the height by approximately 15-20ft.
T1 - Ash: Pollard at approximately 5m above ground level. Reason for works: The tree is showing symptoms consistent with Ash Dieback. The condition is expected to progressively decline as a result of the disease, with recovery considered unlikely. Suggested pollard at approx. 5m with a 5-year re-pollarding management cycle.
Retrospective application for construction of decking to rear of property.
T1 - Monterey cypress. dismantle/fell to ground level due to a section failing in recent storms leaving the remaining part of the tree with a split limb and very little live crown.
T1 English Oak Quercus robur T1 is growing within close proximity of the building Oakridge Retirement apartments opposite flat 14. T1 has been reduced approx. 6 years ago the re growth has started to become heavily weighted. re growth from pruning cuts has a weaker branch union than natural growth. This is more likely to fail and requires maintenance in order to keep the tree safe. There is a busy footpath and car park below the tree as well as being approx. 2m from the building. I would like to reduce this tree to previous points 30% making cuts on vertical growth of up to 15cm and horizontal growth of up to 10cm. this is shown on pic 1 with a red line.